Changing advanced settings on the CL-100 using command line

Created by Bastian Stolk, Modified on Tue, 12 May at 11:29 AM by Bastian Stolk

Changing settings on the CL-100 is not done through a web UI but through a serial connection. This guide contains reference information for all available serial commands.

This guide is intended for power users. Please contact your customer representative if you want to learn more about the CL-100 and it's configuration.

Serial communication parameters

If you want to learn more about the best way to connect to the CL-100, refer to this KB Article: How to connect RS-232/Serial and view FW version on CL-100

Baud rate: 115200

Data bits: 8

Stop bits: 1

Parity: None

Command termination: <CR><LF>

Commands are not case-sensitive.

System settings

Help

Command: help

Description: Get a list of all commands

Example: help

Feedback: Please see "Help" sheet

Help for a specific command

Command: ? <command>

Description: Get help for a particular command

Example: ? set front key

Feedback: Shows command description

Status

Command: status

Description: Get current device status

Example: status

Get firmware version

Command: get version

Description: Get firmware version

Example: get version

Feedback: MCU FW xxxx

Set serial password

Command: set password XXXXXXXX

Description: Set password (6–10 characters)

Example: set password 123456

Feedback: Password has been set

Reboot

Command: reboot

Description: Reboot the device

Example: reboot

Feedback:

Reboot…

System Initializing…

Initialization Finished!

MCU FW xxxxx

Reset

Command: reset

Description: Reset system settings to default

Example: reset

Feedback: Prompts for "yes" to confirm

Reset all

Command: reset all

Description: Reset system + network settings to default

Example: reset all

Feedback: Prompts for "yes" to confirm

Set front key

Command: set front key x

Description: Lock/unlock front button (x=0–1)

Example: set front key 0

Feedback: Front key unlocked

Get front key

Command: get front key

Description: Get front key lock status

Example: get front key

Feedback: Front key unlocked

Set USB-C Network Access

Command: set usbc access network x

Description: Enable/disable USB‑C Ethernet bridge (x=0–1)

Example: set usbc access network 1

Feedback: USB‑C access network: on

Get USB-C Network Access

Command: get usbc access network

Description: Get USB‑C access network status

Example: get usbc access network

Feedback: USB‑C access network: on

Uptime

Command: get uptime

Description: Get system uptime (Day:Hour:Min:Sec)

Example: get uptime

Feedback: 000:00:13:04

Input settings

Set input

Command: set input x

Description: Select input source (x=1–2)

Example: set input 1

Feedback: USB‑C input

Get input

Command: get input

Description: Get input source

Example: get input

Feedback: USB‑C input

Enable/disable autoswitching

Command: set autoswitch x

Description: Enable/disable auto switching (x=0–1)

Example: set autoswitch 1

Feedback: Autoswitch on

Get autoswitch status

Command: get autoswitch

Description: Get auto-switching status

Example: get autoswitch

Feedback: Autoswitch on

Set autoswitch mode

Command: set autoswitch mode x

Description: Set detection type (x=0–1)

Example: set autoswitch mode 1

Feedback: Autoswitch mode: signal detection

Get autoswitch mode

Command: get autoswitch mode

Description: Get auto-switching mode

Example: get autoswitch mode

Feedback: Autoswitch mode: signal detection

Set input priority

Command: set input priority x

Description: Set priority port (x=0–2)

Example: set input priority 1

Feedback: Input priority: USB‑C

Get input priority

Command: get input priority

Description: Get priority port

Example: get input priority

Feedback: Input priority: USB‑C

Get cable status

Command: get input x cable

Description: Get cable status for inputs (x=0–2)

Example: get input 0 cable

Feedback:

USB‑C input cable: connected

HDMI input cable: disconnected

Set HDCP declaration

Command: set input x hdcp declaration y

Description: Set HDCP declaration

Example: set input 0 hdcp declaration 2

Feedback:

USB‑C input HDCP declaration: HDCP 2.3

HDMI input HDCP declaration: HDCP 2.3

Get HDCP declaration

Command: get input x hdcp declaration

Description: Get HDCP declaration for inputs

Example: get input 0 hdcp declaration

Feedback:

USB‑C input HDCP declaration: HDCP 2.3

HDMI input HDCP declaration: HDCP 2.3

Set EDID

Command: set input x edid y

Description: Set EDID (y=1–21) for input(s)

Example: set input 0 edid 1

Feedback: EDID applied to all inputs

EDID options:

Set input ports (x=0~2) EDID (y=1~21) 
x=0: All inputs
x=1: USB-C input
x=2: HDMI input
y=01: Copy EDID from HDMI output (default)
y=02: Copy EDID from USB-C HDMI output
y=03: 4K2K60_444, Audio 2CH PCM
y=04: 4K2K60_444, Audio 5.1CH DTS/DOLBY
y=05: 4K2K60_444, Audio 7.1CH DTS/DOLBY/HD
y=06: 4K2K30_444, Audio 2CH PCM
y=07: 4K2K30_444, Audio 5.1CH DTS/DOLBY
y=08: 4K2K30_444, Audio 7.1CH DTS/DOLBY/HD
y=09: 1080P60_444, Audio 2CH PCM
y=10: 1080P60_444, Audio 5.1CH DTS/DOLBY
y=11: 1080P60_444, Audio 7.1CH DTS/DOLBY/HD
y=12: 720P60_444, Audio 2CH PCM
y=13: 1920x1200, Audio 2CH PCM
y=14: 1680x1050, Audio 2CH PCM
y=15: 1600x1200, Audio 2CH PCM
y=16: 1440x900, Audio 2CH PCM
y=17: 1360x768, Audio 2CH PCM
y=18: 1280x1024, Audio 2CH PCM
y=19: 1024x768, Audio 2CH PCM
y=20: User Defined 1
y=21: User Defined 2

Get EDID

Command: get input x edid

Description: Get EDID mode

Example: get input 0 edid

Feedback: EDID values returned

Set User EDID

Command: set user edid x <y>

Description: Set user‑defined EDID (x=1–2)

Example: set user edid 1 <00 FF FF FF...>

Feedback: User defined EDID loaded successfully

Get User EDID

Command: get edid data x

Description: Get EDID data (x=0–6)

Example: get edid data 0

Feedback: Multiple EDID blocks returned

Output settings

Get output status

Command: get output x cable

Description: Get cable status for outputs

Example: get output 1 cable

Feedback: USB‑C output cable: connected

Set HDCP mode

Command: set output x hdcp y

Description: Set HDCP mode (y=1–4)

Example: set output 1 hdcp 1

Feedback: USB‑C output HDCP: HDCP 1.4

Get HDCP mode

Command: get output x hdcp

Description: Get HDCP mode

Example: get output 2 hdcp

Feedback: HDMI output HDCP: auto

Set output signal

Command: set output signal y

Description: Set output signal state (y=1–3)

Example: set output signal 1

Feedback: Output signal: on

Get output signal

Command: get output signal

Description: Get output signal status

Example: get output signal

Feedback: USB‑C and HDMI output signal: on

Set HDMI 5v output behavior

Command: set HDMI 5V output y

Description: Configure HDMI 5V behavior

Example: set HDMI 5V output 6

Feedback: HDMI 5V output: OFF after 20 minutes

Get HDMI 5v output behavior

Command: get HDMI 5V output

Description: Get HDMI 5V mode

Example: get HDMI 5V output

Feedback: HDMI 5V output: Always ON

Name	Host	Duration	Description
_x_w	plexusav.freshdesk.com	Session	Contains the shard ID at which the account runs on.
_x_m	plexusav.freshdesk.com	Session	Contains the state of the shard.
_helpkit_session	plexusav.freshdesk.com	Session	Your secret key for verifying cookie session data integrity. If you change this key, all old sessions will become invalid!
helpdesk_node_session	plexusav.freshdesk.com	Session	An encrypted hash that stores the secret key and id of the login attempt.
user_credentials	plexusav.freshdesk.com	2 months	Used for user authentication.
wf_order	plexusav.freshdesk.com	Session	Used to check in which the order the tickets are filtered for custom ticket filters eg: due_by, agent_responded_at, requester_responded_at, etc.
wf_order_type	plexusav.freshdesk.com	Session	Used to check if the order is ascending or descending for custom ticket filters.
wf_filter	plexusav.freshdesk.com	Session	Denotes which filter is applied for the tickets list.

Recent Searches

Popular Articles

Articles

Topics

Tickets

Changing advanced settings on the CL-100 using command line

Serial communication parameters

System settings

Help

Help for a specific command

Status

Get firmware version

Set serial password

Reboot

Reset

Reset all

Set front key

Get front key

Set USB-C Network Access

Get USB-C Network Access

Uptime

Input settings

Set input

Get input

Enable/disable autoswitching

Get autoswitch status

Set autoswitch mode

Get autoswitch mode

Set input priority

Get input priority

Get cable status

Set HDCP declaration

Get HDCP declaration

Set EDID

Get EDID

Set User EDID

Get User EDID

Output settings

Get output status

Set HDCP mode

Get HDCP mode

Set output signal

Get output signal

Set HDMI 5v output behavior

Get HDMI 5v output behavior

Was this article helpful?